Форум АНТИЧАТ

Форум АНТИЧАТ (https://forum.antichat.xyz/index.php)
-   *nix системы (https://forum.antichat.xyz/forumdisplay.php?f=124)
-   -   Настройка инета на фряхе (https://forum.antichat.xyz/showthread.php?t=210839)

OSW 11.06.2010 16:46
Настройка инета на фряхе
 
Ось: FreeBSD 8.0
Инет: PPPoE по витой паре.
Сервак: комп с 2-мя сетевухами: nfe0(смотрит в локалку), rl0 (смотрит в инет).

rc.conf

Код:
ifconfig_nfe0="192.168.0.1"
ifconfig_rl0="inet 92.xxx.xx.xx netmask 255.255.255.255"
gateway_enable="YES"
  ppp_enable="YES" 
ppp_mode="ddial" 
ppp_nat="YES" 
ppp_profile="provider"
default_gateway="92.xxx.xx.xx"
ppp.conf

Код:
default:    set log Phase tun command
# you can add more detailed logging if you wish 
set ifaddr 10.0.0.1/0 10.0.0.2/0 
provider:   
set device PPPoE:rl0   
set authname ЛОГИН   
set authkey ПАРОЛЬ   
set dial   
set login   
add default HISADDR
По итогу:
Код:

1# ifconfig
nfe0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=8<VLAN_MTU>
        ether 00:50:8d:63:0a:a9
        inet 192.168.0.209 netmask 0xffffff00 broadcast 192.168.0.255
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=8<VLAN_MTU>
        ether 00:14:78:25:38:28
        inet 92.241.102.14 netmask 0xffffffff broadcast 92.241.102.14
        media: Ethernet autoselect (none)
        status: no carrier
plip0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> metric 0 mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
        options=3<RXCSUM,TXCSUM>
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
        inet6 ::1 prefixlen 128
        inet 127.0.0.1 netmask 0xff000000
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1500
        Opened by PID 390
/etc/resolv.conf - здесь прописал dns вида: nameserver 92.xxx.xx.xx

Инета нет нифига. Пинги не идут ни до www.ya.ru (пишет ping: cannot resolve www.ya.ru: Host name lookup failure), ни до 83.170.209.25 (пишет: ping: send to: no route to host).
При загрузке отчетливо вижу где-то - Network is unreachable.

Я начинающий в познавании фряхи, так что ногами не бить) От гугля уже опухла голова.

POS_troi 11.06.2010 16:57
в ppp.conf

не
Цитата:
set device PPPoE:provider
а
Цитата:
set device PPPoE:rl0
Хэндбук тоже читать нужно уметь

OSW 11.06.2010 16:58
Цитата:
Сообщение от POS_troi
в ppp.conf

не


а


Хэндбук тоже читать нужно уметь
Эт я ошибся щас в посте. Так в оригинале написано rl0

POS_troi 11.06.2010 17:06
логи ppp в студию


Также попробуй привести ppp.conf к такому виду
PHP код:
default:
  set log Phase tun command  
  set ifaddr 0 0
provider:
  set device PPPoE:rl0
  set authname YOURLOGINNAME
  set authkey YOURPASSWORD
  set dial
  set login
  add default HISADDR 
Ну и соответственно в консольке

PHP код:
ppp -ddial provider 
кстати

Цитата:
PPPoE по витой паре.
что находится на другом конце кабеля?

OSW 11.06.2010 17:35
Логи ppp:

Код:
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: Disconnected!
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: Disconnected!
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: lcp -> logout
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: lcp -> logout
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: Disconnected!
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: Disconnected!
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: logout -> hangup
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: logout -> hangup
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: Connect time: 17 secs: 100 octets in, 130 octets out
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: Connect time: 17 secs: 100 octets in, 130 octets out
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: 42 packets in, 45 packets out
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: 15 packets in, 15 packets out
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase:  total 13 bytes/sec, peak 18 bytes/sec on Fri Jun 11 17:30:52 2010
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase:  total 13 bytes/sec, peak 18 bytes/sec on Fri Jun 11 17:30:52 2010
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: hangup -> opening
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: hangup -> opening
Jun 11 17:31:03 1 ppp[1034]: tun1: Phase: deflink: Enter pause (3) for redialing.
Jun 11 17:31:03 1 ppp[1057]: tun2: Phase: deflink: Enter pause (3) for redialing.
Jun 11 17:31:06 1 ppp[390]: tun0: Phase: deflink: Connected!
Jun 11 17:31:06 1 ppp[390]: tun0: Phase: deflink: opening -> dial
Jun 11 17:31:06 1 ppp[390]: tun0: Phase: deflink: dial -> carrier
Jun 11 17:31:06 1 ppp[1057]: tun2: Phase: deflink: Connected!
Jun 11 17:31:06 1 ppp[1034]: tun1: Phase: deflink: opening -> dial
Jun 11 17:31:06 1 ppp[1057]: tun2: Phase: deflink: opening -> dial
Jun 11 17:31:06 1 ppp[1034]: tun1: Phase: deflink: dial -> carrier
Jun 11 17:31:06 1 ppp[1057]: tun2: Phase: deflink: dial -> carrier
Jun 11 17:31:08 1 ppp[390]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "SR6602-ATs5000fe27f8b45")
Jun 11 17:31:08 1 ppp[390]: tun0: Phase: Received NGM_PPPOE_SESSIONID
Jun 11 17:31:08 1 ppp[390]: tun0: Phase: Received NGM_PPPOE_SUCCESS
Jun 11 17:31:08 1 ppp[390]: tun0: Phase: deflink: carrier -> login
Jun 11 17:31:08 1 ppp[390]: tun0: Phase: deflink: login -> lcp
Jun 11 17:31:08 1 ppp[390]: tun0: Warning: deflink: Oops: Got 18 bytes but 50 byte payload - dropped
Jun 11 17:31:08 1 ppp[1034]: tun1: Phase: Received NGM_PPPOE_ACNAME (hook "SR6602-ATs5000fe27f8b45")
Jun 11 17:31:08 1 ppp[1057]: tun2: Phase: Received NGM_PPPOE_ACNAME (hook "SR6602-ATs5000fe27f8b45")
Jun 11 17:31:09 1 ppp[390]: tun0: Warning: deflink: Reducing configured MRU from 1500 to 1492
Jun 11 17:31:11 1 ppp[390]: tun0: Warning: deflink: Oops: Got 18 bytes but 50 byte payload - dropped
Jun 11 17:31:11 1 ppp[1034]: tun1: Phase: deflink: Disconnected!
Jun 11 17:31:11 1 ppp[1034]: tun1: Phase: deflink: carrier -> hangup
Jun 11 17:31:11 1 ppp[1034]: tun1: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out
Jun 11 17:31:11 1 ppp[1034]: tun1: Phase: deflink: 42 packets in, 45 packets out
Jun 11 17:31:11 1 ppp[1034]: tun1: Phase:  total 0 bytes/sec, peak 0 bytes/sec on Fri Jun 11 17:31:06 2010
Jun 11 17:31:11 1 ppp[1034]: tun1: Phase: deflink: hangup -> opening
Jun 11 17:31:11 1 ppp[1034]: tun1: Phase: deflink: Enter pause (30) for redialing.
Jun 11 17:31:11 1 ppp[1057]: tun2: Phase: deflink: Disconnected!
Jun 11 17:31:11 1 ppp[1057]: tun2: Phase: deflink: carrier -> hangup
Jun 11 17:31:11 1 ppp[1057]: tun2: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out
Jun 11 17:31:11 1 ppp[1057]: tun2: Phase: deflink: 15 packets in, 15 packets out
Jun 11 17:31:11 1 ppp[1057]: tun2: Phase:  total 0 bytes/sec, peak 0 bytes/sec on Fri Jun 11 17:31:06 2010
Jun 11 17:31:11 1 ppp[1057]: tun2: Phase: deflink: hangup -> opening
Jun 11 17:31:11 1 ppp[1057]: tun2: Phase: deflink: Enter pause (30) for redialing.
Jun 11 17:31:14 1 ppp[390]: tun0: Warning: deflink: Oops: Got 18 bytes but 50 byte payload - dropped
Jun 11 17:31:20 1 last message repeated 2 times
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: Received NGM_PPPOE_CLOSE
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: Device disconnected
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: Disconnected!
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: lcp -> logout
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: Disconnected!
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: logout -> hangup
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: Connect time: 17 secs: 100 octets in, 130 octets out
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: 97 packets in, 100 packets out
Jun 11 17:31:23 1 ppp[390]: tun0: Phase:  total 13 bytes/sec, peak 18 bytes/sec on Fri Jun 11 17:31:12 2010
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: hangup -> opening
Jun 11 17:31:23 1 ppp[390]: tun0: Phase: deflink: Enter pause (3) for redialing.

OSW 11.06.2010 17:37
Цитата:
Сообщение от POS_troi
Также попробуй привести ppp.conf к такому виду
PHP код:
default:
  set log Phase tun command  
  set ifaddr 0 0
provider:
  set device PPPoE:rl0
  set authname YOURLOGINNAME
  set authkey YOURPASSWORD
  set dial
  set login
  add default HISADDR 
Ну и соответственно в консольке

PHP код:
ppp -ddial provider 
кстати


что находится на другом конце кабеля?

Все привел к нужному виду.
На другом конце кабеля - хз. Я знаю, что в кабинет проведен инет по витухе, есть логин и пароль. А что там стоит - хз.

POS_troi 11.06.2010 17:42
Ну так там может быть и VPN . Выясняй.

OSW 11.06.2010 17:44
http://www.citycomm.ru/support/detail.php?ID=82 - отсюда берем инет. ВПНа нет.
Настройки сабжевые:
Цитата:
citycomm-pppoe:
set device PPPoE:"имя вашего ethernet-интерфейса"
set dial ""
set authname "логин, полученный от ISP"
set authkey "пароль, полученный от ISP"
set ifaddr 0 0
add default HISADDR


Время: 05:56